How Do I Manually Start Hunter Pro C?

  1. How can I launch Hunter Pro C from the command line? Continue to keep the button down for 2 seconds while the dial is in the RUN position.
  2. Program A is selected by default when this feature is activated. By hitting the PRG program key, you can choose between programs B and C.
  3. The station’s identification number will be flashing
  4. To begin with a certain station, use the button to navigate to that station.

Hunter controllers provide you the ability to launch a station or a whole program from the command line. This may be accomplished by switching the dial from Run to Manual Single Station or Manual All Stations, confirming that the stations you wish to activate have sufficient run time, and then switching back to the Run position.

How do I connect my Hunter Pro-C controller to my power module?

Connect one wire to one of the SEN terminals on the power module, and another wire to the other SEN terminal on the power module. 16 A SRR or ICR remote control is connected in this manner (Not Included) In addition to the Pro-C controller, a SmartPort®wiring harness is included, enabling for quick and easy integration of Hunter remote controllers.

How do I program my Pro-C to start and advance?

Pro-C – Manual Start and Advance with a Single Touch 1 While the dial is in the RUN position, press and hold the button for 2 seconds.2 2 Program A is selected by default when this feature is activated.By hitting the PRG program key, you can choose between programs B and C.3 The station number will be flashing in the background.

You might be interested:  Can You Use An Ott Light For Plants?

4 To begin with the station you want to start with, use the button to navigate to it.

How do I use the Pro-C with single station manual start?

The Pro-C is capable of completing that duty with a single station manual start. Simply set the dial to Manual-One Station, press the arrow buttons to navigate to the selected station, and then set the dial to the Run position to begin running. If desired, the user may additionally adjust the run time setting by increasing or decreasing it.

How do you manually turn on Hunter core?

X-Core – Manual Start and Advance with a Single Touch

  1. Hold down the arrow (>) button for a total of two seconds.
  2. Default application A is selected by default in this feature.
  3. The station’s identification number will be flashing.
  4. By pressing the arrow (>) button, you may go to the station you want to start with.

How do I start my hunter sprinkler system?

Checklist for the Beginning of the Spring Season

  1. Start by slowly opening the system’s main water valve to allow the pipes to gradually fill with water.
  2. By manually activating all zones from the controller, you can check that each station valve is functioning properly.
  3. Walk through each station on the controller, making sure that the zone is operating properly

Why is my Hunter irrigation system not working?

Typically, the rain sensor will be activated, which will prevent your sprinklers from watering as intended. You may already have a rain sensor installed on your sprinkler system. If this is the case, move your sensor bypass switch to the ‘BYPASS’ position (on an SRC, adjust the dial to the ‘RUN’ position) (Bypass Sensor position).

You might be interested:  Do Los Angeles Taxis Take Credit Cards?

How do I test my Hunter Pro C sprinkler system?

To start the test program, do the following:

  1. Press and hold the PRG button for a few seconds. The station’s identification number will be flashing
  2. Press the or button to move the cursor to the station where you would like the test program to begin with. Set a run time of up to 15 minutes by pressing the and buttons simultaneously.
  3. When the 2 second delay is over, the testing procedure is initiated.

How do I turn on my hunter sprinkler system after winter?

Following the winterization of a sprinkler system, there are several steps to do.

  1. Locate the primary shut-off valve of the system
  2. Locate the vacuum breaker.
  3. Close the vacuum breaker test valves if they are open.
  4. The vacuum breaker’s shutoff valves should be opened.
  5. Replace the main valve bleeder cap if it is necessary.
  6. Open the main valve slowly and carefully.
  7. Check the system’s functionality.
  8. Make sure that the vacuum breaker and valves are in working order.

How do you manually turn on a Hunter sprinkler?

The manual run is performed at all stations.

  1. Maintaining pressure on the button for three seconds is recommended.
  2. By hitting the button, you may select a program.
  3. If the amount of time for the station to water differs from the amount of time displayed, use the or buttons to pick the amount of time for the station to water.
  4. Using the button, you may go on to the next stop.

How do I program my Pro-C to start and advance?

Pro-C – Manual Start and Advance with a Single Touch 1 While the dial is in the RUN position, press and hold the button for 2 seconds.2 2 Program A is selected by default when this feature is activated.By hitting the PRG program key, you can choose between programs B and C.3 The station number will be flashing in the background.

You might be interested:  How Do You Use Construct In A Sentence?

4 To begin with the station you want to start with, use the button to navigate to it.

How do I program Pro-C to water without the dial?

A Quick Tip for Using the Pro-C with a Hunter Controller for One-Touch Manual Start and Advance Manual Operation You may also use the dial to activate a watering program without using the dial. While the dial is in the RUN position, press and hold the button for 2 seconds to start the engine.

How do I program stations on the controller?

Using the and buttons, you can quickly navigate among the stations while using the and buttons to change the run times of the stations. To begin program A, the controller will automatically start if no buttons are pushed between steps 2 and 3. To begin with the station you want to start with, use the button to navigate to it. Immediately following a 2-second pause, the program will begin.

Leave a Reply

Your email address will not be published. Required fields are marked *