Silverglo insulation panels where to buy?

Who makes SilverGlo insulation?

Basement Systems, Inc. announces the launch of SilverGlo insulation board, an innovative rigid foam insulation product. Basement Systems, Inc., a leader in the basement and crawl space industries with dealers in six countries, has recently developed a new insulation product called SilverGlo foam board insulation .

What is SilverGlo insulation?

SilverGlo ™ is an expanded polystyrene foam insulation that’s been infused with graphite during its creation to improve its insular ability by 24%. Combined with its silver radiant heat barrier on the visible surface, it provides an insulation rating of R-11 on your crawl space walls.

How much does foam board insulation cost?

Spray Foam Insulation Cost Per Square Foot Spray foam insulation costs $0.44 to $1.50 per board foot. A board foot is one square foot that is one-inch thick, or one square foot that’s covered by one inch of spray foam insulation . Expanding foam insulation costs from about $0.50 to $2.50 per square foot.

How much does rigid insulation cost?

The Cost of Rigid Foam Insulation

Insulation Rating Material per Sq. Foot Labor per Sq. Foot
R-13 $0.75 to $0.90 $0.90 to $1.25
R-19 $1.10 to $1.30 $0.90 to $1.30
R-21 $1.20 to $1.45 $0.95 to $1.30

What is the R value of silverboard?

Features

Compressive Strengths 12psi (88.2 kPa), 21psi (147.9 kPa), 35psi (245.5 kPa) and 44psi (306.1 kPa)
R – Value /inch 5 hr.ft2.F/Btu (0.88 m2K/W per 25mm)
Vapor Permeance 0.075 US perms (4.27 ng/Pa.s.m2)

How do you install foam insulation in the attic?

How Do You Install Rigid Foam Board ? Measure the space between rafters and cut the board to fit. Use a chalk line or T-square to mark where it needs to be cut. You can use a utility knife to cut using the same cut and snap process you use with drywall. Put the board between the rafters.

You might be interested:  What did thomas jefferson do?

How much does it cost to insulate a 1500 sq ft house?

Cost : Blown-in insulation is perfect for the weekend warrior looking to get the job done cheaply. There is little learning curve involved with the application, and a DIY job will cost you about $500. Calling in the pros, on the other hand, will run you about $1,500 to $2,000 for an average 1500 square foot home.

What is the best insulation for a crawl space?

The best insulation material for crawl spaces is rigid foam insulation board. Instead of installing the foam insulation between floor joists in the crawl space, the foam board is installed against the crawl space foundation walls .

How thick should foam board insulation be?

It comes in standard-size 4×8 sheets, and smaller sizes, in many different thicknesses from 1/4 inch to 2 inches. Some types of thicker foam board insulation are available, but they may need to be special ordered. Foam board insulation is easy to use and is a great DIY way to add some insulation .

What is the difference between pink and blue foam board?

Both are manufactured using the same process and contain similar chemical components. The two products also have the same insulating power. However, blue foam boards are manufactured by Dow Chemical Co. whereas the pink foam boards are manufactured by Owens Corning company.

What is the cheapest insulation board?

Polystyrene EPS & XPS Rigid Insulation Boards Polystyrene insulation can be the cheapest board insulation . Polystyrene insulation comes in two flavours EPS (Expanded) and XPS (Extruded). EPS & XPS features low water absorption properties.

You might be interested:  FAQ: How many dogs can you own in ohio?

How much does it cost to insulate a 1000 sq ft attic?

The cost to insulate an attic with blown-in insulation runs from $600 to $1,200, assuming it is 1,000 square feet in size. If you choose to hire a professional, expect to pay from $40 to $70 an hour for labor in addition to the cost of materials.

What is the R value of 2 inch foam board?

Also called Styrofoam insulation, this is the least expensive material. It provides R-values that range from 3.6 to 4.2 per inch .

What is the R value of 4 inch rigid insulation?

EPS is the insulation used most widely in insulated concrete forms and structural insulated panels (SIPs). EPS has the lowest average R – value of the three most common types of rigid – foam insulation , around R – 4 per inch . It also is the least expensive.

Leave a Reply

Your email address will not be published. Required fields are marked *